Sagemcom router: step-by-step setup for a kettle. Universal router from Rostelecom Updating the sagemcom f st 2804 v7 modem

Universal router Sagem FAST 2804 in one of its incarnations it is ADSL modem with very good functionality and a pleasant appearance. In fact, this device can be put on a par with such models as D-Link DSL-2640U/NRU, Acorp W422G And ASUS DSL-N10. A very useful feature is the presence USB ports- allows, if necessary, to organize a backup channel using 3G modem .

For setting up any special difficulties Sagem FAST 2804 doesn't, but the web interface is a bit confusing. The device address on the network is standard - http://192.168.1.1, login admin and password admin. Password for superadmin - Is$uper@dmin.

Step 1. Removing an existing PPP connection. Select a section Additional settings -> WAN service.

In the table by default there is already one existing connection, put a checkmark Delete and press the button Delete.
Step2. Delete existing WAN port settings. Select a section Additional settings -> Second level interface -> ATM PVC interface.

There is also a default PVC 8/32 created here, which does not suit us. Check the Delete box and click the Delete button.
Step3. Creating a PVC connection. After the connection is deleted, press the button Add and create a new one:

We set VPI/VCI parameters - in branches Rostelecom single standard - 0/33 . Type DSL Link the default is EoA- it is also used for the mode PPPoE and for Bridge. Encapsulation mode - LLC. Press the button Apply/Save.
Step4. Create a new connection on a new ATM connection. Go to the section WAN service:

To add a new connection, click the button Add.

The next step is to select the physical interface atm0 and press Further.

If you need to configure the connection mode on the modem transparent bridge(Bridge)- for example for IPTV c VPI/VCI 0/50- select a mode Bridging and press Further. You get this result:

Click Apply and get a modem configured in mode Bridge.

You get this result:

Click Apply and get the modem configured in bridge mode .

If you need to configure the modem in router mode(Router)- choose PPPoE and press Further:

In this window, enter the username and password given to you upon connection. In field PPPoE Service Name you can enter the name of the connection - for example inet. Next, check the box retry PPP on authentication failure and press the button Further.

Here we leave everything as default and click Further.

Settings DNS We also leave automatic, press Further.

The connection has been created, click Apply/Save. This completes the basic connection setup on Sagem fast 2804 Finished.

In the future, if you need to re-enter your login and password for PPPoE connections- select an item Internet connection:

We are already changing here login And password, press Apply/Save.
After setup, reboot the device with the new settings. To do this, go to the section.

and wait until the device restarts. If you did something wrong and are in doubt - reset the device to factory settings and configure again. To reset the configuration to factory settings, go to the section Control -> Settings options -> Reset:

If the VPN doesn't work (it gives error 619):
Let's go: Additional settings -> NAT -> Port trigger.
We configure the TCP\UDP protocol port 1723, ( if you open TCP separately and UDP 1723 separately, it will not work!!!). Save and connect the VPN.

Modem setup program + firmware (stable, dated 10/16/2012): Official site

Thanks to Alien, Anatoly, for collecting information “piece by piece”.

Many owners of the Rostelecom Sagemcom f st 2804 v7 router prefer to configure the Internet and IP-TV themselves, since modern firmware versions allow even an ordinary user to do this. If you also wondered how to configure the Rostelecom fast 2804 v7 router, then this article is just for you. In it we will analyze in detail the process of setting up the connection itself and the parameters of the future wireless network.

Preparing the router

First of all, we need to correctly connect the Rostelecom Sagemcom f st 2804 v7 router. To do this, connect the power cord to the rear panel. Then, if you are using a telephone connection, insert the Internet cable into the first slot. If your home has fiber optics or any other connection using a standard Ethernet cable, insert it into the first of the next four ports.

After that, turn the router face down and look at the indicators that light up:

• “Power” – lights up in any case if the router is connected to the network;
• “DSL-link” - shows us that the fast 2804 Rostelecom router receives a signal from the provider’s servers, so it should be on;
• “WiFi” – enabled by default in all Rostelecom modems;
• “LAN” – lights up if the cable is connected correctly.

Important: as you understand, even with factory settings, the router can “distribute” a WiFi signal. So there is no need to configure it separately. But, if you want to change the network name or the set password, you can find instructions for this later in the article.

I would also like to note that while setting up the Rostelecom f st 2804 v7 router, you may have a question: what is this USB port on the back of the case? Answer: This is a standard USB for connecting your portable Internet (connect) in case of a loss of connection with the main provider or the need to use this type of repeater on several devices at once.

Setting up a Rostelecom fast 2804 v7 router

The first stage of setup is entering the main interface. It is done through the browser:

• launch an internet browser that is convenient for you;
• In the address bar field, enter the ip of your router: 192.168.1.1;
• In the Login and Password fields, enter the keyword “admin” in lower case.

If everything is done correctly, you will be redirected to a new page in the same tab, where the main menu will be located on the left on a blue background. We will work with him.

Resetting basic settings

If you are setting up a Rostelecom fast 2804 router that has already been used in another place or because the settings have been lost, then all settings must be returned to the factory values. You can do this as follows:

• go to the last menu item “Management”;
• open the first subsection “Settings”;
• find and click on the submenu item “Reset”;
• in the middle of the page we see a button “Restore default settings”;
• click on it;
• Click OK in the confirmation window that pops up;
• We wait until the reset operation is completed and we will be transferred again to the main page of the web interface.

All is ready! Now the Rostelecom fast 2804 v7 router can be configured.

Removing unnecessary factory connections

Since after resetting all parameters the router creates several initial non-working connections, the first thing you need to do is delete them so that there are no errors during operation. This is done in several steps.

• in the main menu on the left we find “Advanced settings”;
• in the submenu that pops up, open “WAN service”;
• in the updated window we see a table of three points (three connections), on the left side of which there is a “Delete” column, put a checkmark in all of them;
• Under the table we find the “Delete” button, click on it;
• in the updated window we see an empty table.

• still in the same place in “Advanced settings” open the item “Second level interface”;
• the first section of the submenu is “ATM PVC Interface”;
• delete the only table item in the same way as in the previous step;
• waiting for the page to update;
• open the last item of the submenu that pops up – “ETH Interface”;
• delete the existing row in the table in the same way;
• We observe a page reload and the disappearance of the remote configuration;

Direct setup by Rostelecom Sagemcom f st 2804

After the cleaning is completed, the Rostelecom fast 2804 router is deeply configured:

• return to the “ATM PVC Interface” and click on the “Add” button;
• on the page that opens, indicate the Internet connection data: VCI and VPI;
• We leave all other points unchanged;
• scroll down the page – “Apply/Save” button;
• in the same way, we add a connection for IP-TV by clicking on “Add” (only the VCI will change, in most cases).

The Rostelecom f st 2804 v7 router is connected on the “WAN service” tab:

• click “Add”;
• select the created configuration – “Next”;
• indicate the type of service used (in most cases PPPoE);
• on the page that opens, enter the user data (login/password) specified in the Internet service agreement;
• In the same place, select the desired name for the connection (“PPPoE Service Name”);
• check that there is a checkmark next to the item “PPP repeat...”;
• click “Next”;
• Move the “ppp1” route you created to the left column if it is in the right. then move the USB connection in the opposite direction;
• We perform the same operation and “Next” again.

We see the list of final settings and make sure that in the second line opposite “NAT” the “Enabled” option is indicated. If this is not the case, we return to the stage of specifying the connection login and password and check the boxes on this page that include NAT and Firewall. Apply the changes made.

How to configure the fast 2804 v7 Rostelecom router for IP-TV? Very simple! We repeat the first three points from the algorithm above, only we select the second created configuration (in the second step) and the Bridge connection type instead of PPPoE (in the third). Move on, save the settings and voila! There is Internet!

How to connect the Rostelecom f st 2804 router to WiFi

The firmware of the Rostelecom f st 2804 v7 router implies initial settings for a wireless connection. To change them, you need to do the following:

• main menu item “WLAN Settings”;
• go to the “Main” submenu;
• check the box to enable wireless communications;
• change the SSID to any network name you like and save the changes;
• go to the “Security” submenu;
• disable WPS (the weak point of the wireless connection, which is easy to hack);
• we check that our network name is selected and change the standard password to the one we created (the field after the “Authentication” item);
• We save the adjustments made.

That's all, we figured out how to configure the Rostelecom Sagemcom f st 2804 router on our own.

Summarizing the above material, we can say that connecting a router to the Internet comes down to four steps:

• reset;
• removing standard connections;
• creating a new PPPoE port;
• changing WiFi settings.

Having mastered these steps, you yourself will be able to configure and tell others how to connect the Rostelecom f st 2804 router to the network.

Important: the VPI and VCI values ​​discussed in the article are unique for each region of Russia. Therefore, they must first be clarified with the provider, or found on the Internet.

The entire algorithm described above is clearly demonstrated in this video:

What other questions did you have during setup?

The f@st 2804 v7 rev1 router is a universal network equipment necessary for connecting end devices to the Internet and IP-TV via an Ethernet cable, telephone line and wireless cellular communication via a 3G/LTE modem.

And this article discusses in detail the configuration of the Rostelecom fast 2804 v7 router, as well as its main characteristics and the configuration of a 3g modem.

By the way, the advantage of this router is that, at its relatively low cost, it supports almost all the functions necessary for the average user: from setting up a print server to the ability to reserve the main Internet channel.

Sagemcom f@st 2804 v7: characteristics

In addition to the standard capabilities of distributing Internet traffic and IP-TV between several functional nodes of the local network, the f@st 2804 router also supports additional functions such as:

• - creation of a backup Internet channel (in case of a power outage or problems on the side of the main communication provider);
• - the ability to use the router as a print server (to connect several user devices to a network printer);
• - the ability to use f@st 2804 as a network drive (in other words, when you connect a hard drive to the router, it can be “used” as a miniature server).

On the front panel of Sadzhemkom fast 2804 there is a block of router indicators:

1. Power indicator. The normal operation of the modem is indicated by the constant green color of the Power indicator.

If this LED lights up red, then the fast 2804 modem is in emergency recovery mode, which starts when the router software is slightly damaged.

2. DSL indicator, which with a constant green light notifies the user about a normal ADSL connection, and with rapid blinking - about the establishment of this connection.

3. Internet indicator, which should glow solid green if the connection is successful through the Internet account.

4. WLAN indicator, which lights up green when the wifi module is activated on the router.

5. Several ETH indicators that light up when external devices are connected to the corresponding Ethernet port via a network cable.

6. WPS indicator, green color means successful connection with the user device via .

7. USB indicator indicating successful connection of external media to the sagemcom fst 2804 v7.

On the back of the fast 2804 v7 rev1 there are:

One ADSL port for connecting to the Internet via a telephone line;

4 LAN ports (for connecting to a router via twisted pair);

A small hole with a Reset button recessed into the case (to reset the router to factory settings, you need to press this button with a paper clip or a needle and hold it for 10 - 15 seconds);

Power connector (to which the sagemcom f st 2804 v7 power supply is connected);

Power button;

On the right side panel of Sajekom fast 2804 there are:

Connecting sagemcom f st 2804 v7

When connecting to the Internet via an ADSL telephone line, the cable provided by the provider should be connected to the splitter input (LINE), and a telephone set and router should be connected to its PHONE and MODEM outputs, respectively.

When connecting to the Internet using WAN Ethernet technology, the provider’s network cable must be connected to the first LAN connector of the Sadzhemkom 2804 router.

Modem Rostelecom f st 2804 v7: setup instructions

If the computer (on which the Rostelecom fast 2804 v7 router will be configured) is correctly connected to the router via twisted pair, then the following indication should be present on the router:

The first indicator lights up solid green;
- second indicator – slowly blinking green;
- fourth indicator – lights up or blinks green;
- one of the LAN ports – lights up or blinks green.

The setup of the Rostelecom fast 2804 v7 router described in this manual corresponds to the initial setup of the device. If the router has been in use before, it is recommended to first reset the device to factory settings using the Reset button.

Configuring the Sadzhemkom 2804 router using the Hardware Setup Wizard

To launch the fast 2804 router setup wizard, insert the disk supplied with the device into the computer's CD drive and follow the further instructions of the program.

Once the software installation is complete, the “Setup Wizard” will automatically launch (which can also be launched through the “Start” menu -> “Programs” -> “Hardware Setup Wizard”).

During the automatic configuration of the Rostelecom fast 2804 router, the following operations are performed:

• - updating the router software from the installation disk;
• - selecting the desired router configuration;
• - configuration of PPPoE connection and 3G reservation;
• - diagnostics of equipment performance;
• - installing the latest version of the router firmware from the update server.

Manual configuration of the Rostelecom fast 2804 v7 router

In the absence of an installation disk, it is recommended to configure the Wi-Fi router f@st 2804 manually. To do this, in the address bar of any Internet browser installed on your computer, enter the combination of numbers 192.168.1.1 (the static IP address of the device indicated on the service label on the back of the sagemcom 2804) and press the “Enter” key.

It is recommended to subsequently change the default authentication data (login/password) to unique ones to protect your router from unauthorized access.

Initially, you will be taken to a page with basic technical information about the device.

Modem Rostelecom f@st 2804 v7: Ethernet connection instructions

1. To configure the fast 2804 v7 modem by Rostelecom, in the left vertical menu, select the “Advanced settings” section:

Here, first delete all connections created by default in the “Wan service” subsection;

In the “Layer 2 Interface” tab, remove “DSL ATM”;

Go to the “ETH interface” tab: select “eth0/eth0” from the drop-down list, set “VLAN/MUX Mode” in the connection mode and click the “Apply/Save” button.

2. When all unnecessary settings have been “cleaned up”, return to the “Wan service” tab, click the “Add” button and select the “eth0/eth0” port set in the previous step. Click "Next".

3. In the next window, select the service type “PPPoE” and write the value “-1” in the bottom two lines. Click "Next"

4. At the next stage, in the “PPP username” and “PPP password” windows, enter the username and password for connecting to the Internet from your agreement with the provider. Click "Next"

5. If the new window contains the columns “Enable NAT” and “Enable Firewall”, then place a marker next to each of them. In the subsequent windows (with the standard configuration of the Rostelecom fast 2804 v7 router), you do not need to change anything - click “Next” several times and at the end “Apply/Save” to make changes to the router settings.

How to configure a Rostelecom fast 2804 v7 router with an ADSL connection?

When connecting to the Internet via a telephone line, after deleting the standard settings in the first step of the previous instructions, go to “Advanced settings”, then “2nd level interface” and click the “Add” button.

• - in the VPI and VCI columns, enter the data from the agreement with the provider (they can also be clarified in technical support) and click “Next”;
• - go to “WAN service”, click “Add” and select an interface in accordance with the data entered in the previous window. Click Next.
• - in “WAN Settings” select the “router” type and click “Next” again
• - enter the login, password and PPPoE service name from the Internet connection agreement;
• - set the marker to the fields “Retry PPP on authentication error” and “Enable IGMP Multicast Proxy”, then double-click “Next” and “Apply”.

sagemcom f st 2804 v7: wifi setup

Go to the menu section “WLAN Settings”;
- check the boxes “Enable wireless communication” and “Enable multicast transmission via wireless network (WMF)”;
- enter “SSID” (this is the name of your Wi-Fi access point) and click “Apply”;

- go to the “Security” section;
- if you wish, you can disable the WPS option;
- select the authentication type “WPA-PSK”;
- enter the Wi-Fi password;
- select WPA encryption “TKIP+AES”;
- click “Apply” to save the new settings.

Fast 2804 v7 router: setting up a 3g modem

Below is an approximate list of supported sagemcom fast 2804 v7 rev 1 3G USB modems
- HUAWEI: E220, E1550, E1552, E1752, E160G, E176G, E180, E169G, E150, HW601
- ZTE: MF112, MF626, MF627, MF180, MF190A
- Alcatel: X220, X080
- Airplus: MCD-650
- Withtel: WMU-100A
- Anydata: ADU-300
- Yota: LU156 (LTE)

To configure the 3g modem setup on the fast 2804 v7 router:

Connect the device to the special USB connector on the side panel of the router;

Go to the “3G Configuration” section of the web interface and set the marker to “Enable 3G reservation”;

With these settings, when the main (ADSL or Ethernet) Internet connection is disconnected, the router will automatically switch to the 3G/LTE channel.

One of the largest providers of telecommunications services, PJSC Rostelecom, is constantly expanding the range of offers for users. In this regard, a need arose for a universal device with which the user can connect to the Internet, use interactive television and wireless mobile communications. To do this, you will have to buy and figure out how to configure a router from Rostelecom Sagemcom f st 2804 v7 rev 1. This is not difficult to do using our tips.

The main task of routers is to distribute traffic between Internet users and those who use interactive television (IPTV) services. The Rostelecom Sagemcom f st 2804 v7 rev 1 router, in addition, is capable of performing other equally important tasks, including:

• The ability to create a backup Internet channel, and this is extremely important, given the possibility of an unexpected power outage.
• Use as a network server, for which it is possible to connect a hard drive.
• A router can be used to connect multiple devices to a network printer.

The device has a classic appearance and standard settings, and you can learn a lot about the status of its operation by looking at the front panel of the device. Here you will find an on/off indicator, a DSL indicator indicating the presence of an ADSL connection, an Internet connection indicator, and a WLAN indicator indicating that the Wi-Fi module is ready for operation. There are also indicators indicating that one or more devices are connected to the Ethernet port, as well as the presence of a connection via WPS. If portable Internet was connected to the router, the USB indicator will give a signal.

On the back of the device you will find a power connector, an on/off button, and a hidden RESET button that allows you to return to factory settings, if necessary. There is also an ADSL connector and several LAN connectors. Several functional buttons and a USB connector are located on the right side panel, and their purpose can be found in the instructions for the Rostelecom Sagemcom f st 2804 v7 rev 1 modem, supplied with each device.

Connecting wires

Before proceeding with connecting the device, you need to remove it from the packaging and install it in the desired location. Let's move on to the connection, for which we take it out of the package and connect the power cord. If you are using a telephone connection, you must insert a telephone cable connected through a splitter to the telephone line. If you use fiber optic Internet, insert the Internet cable into one of the four LAN connectors.

Let's start studying the status of the indicators on the front panel. The POWER button will indicate that the device is connected to the network, while the DSL-Link indicator will indicate that the router is receiving a signal from the service provider. As for the LAN indicator, its signal indicates that the cable is correctly connected. After making sure that the device is working, you can proceed to the basic settings of the Sagemcom f st 2804 v7 rev 1 router from PJSC Rostelecom.

Login to the WEB interface and reset all settings

Before you start working, you will have to log in and enter the online interface, for which you just need to launch one of the installed browsers. In the address bar of the browser, enter the address of the router for subsequent configuration of the Sagemcom f st 2804 v7 rev 1 router under Rostelecom, which can be found on the bottom cover of the device, although quite often you have to use a used router, which means that the sticker with the address may be missing . You can find it by examining the connection properties, but you will need the “Main Gateway” data. After entering the address, you will have to log in, and the authorization data is also on the sticker. Now that you were able to enter the settings of the Sagemcom router, let's proceed to the network connection settings and other necessary settings.

Important! The RTK router comes with a disk that allows you to configure the device automatically, but experts do not recommend doing this, since in this case a large number of “junk” connections will appear.

Direct Internet setup

To complete the setup process, connecting to the Internet and final configuration of the Wi-Fi router f st 2804 v7 rev 1, go to the “Advanced” tab, where in the WAN service section you will have to get rid of all existing connections. In a similar way, unnecessary information from the “2nd Level Interface” section is also deleted. After clicking on the “Add” button, the Sagemcom f st 2804 equipment setup wizard will prompt you to enter VCI and VPI data, and they differ depending on your location. Effective assistance will always be provided by the RTK technical support service. We apply and save the settings, then in the WAN service tab we add the newly created connection and indicate its type (standard PPPoE).

Click to enlarge

Remember! At the next stage of setting up fast 2804 v7, you will be asked to enter the user login and the key for the PPP connection. You can find them in the agreement with PJSC Rostelecom.

After entering your registration data, don’t forget to check the box next to “Repeat PPP”. You can confirm the final configuration of the basic parameters of the installed router by clicking the apply and save button, after which you can move on to other settings. Next we will tell you how to install and configure the fast 2804 v7 Wi-Fi router for dummies, and this is also not difficult to do.

Setting up a Wi-Fi connection

To configure the configuration and universal setup of the Sagemcom Wi-Fi router from Rostelecom, you need to go to the “Main” section of the WLAN category, where you will have to enable the wireless network and multicast transmission (you will find these items without problems). In the “Security” category, it remains to specify the authentication options (WPA-PSK) and encryption method (TKIP and AES). After entering an access key consisting of at least eight characters, the settings can be saved by pressing the button of the same name. At this point, setting up the router can be considered complete, but to make sure that you have completed the simple task of setting up the Sagemcom f st 2804 v7 rev 1 router from Rostelecom, you need to reboot - in the “Management” section, click the appropriate button. After the reboot, you can start working.

Click to enlarge

Setting up for working with a TV set-top box

In conclusion, I would like to talk about how to configure a router if you want to work with a TV set-top box. This is also easy to do - just find the “Second Level Interface” tab in the settings where you will have to create an additional connection with new VPI and VCI values. Traditionally, a new object is created in the WAN service (a new connection is selected). In the LAN tab, the DHCP server is disabled, after which the “IGMP Snooping” and “IGMP Proxy on the Bridge” parameters are activated.